jffs2: notice: (290) check_node_data: wrong data CRC

I have made a firmware with 3.10.49 SDK.
I have installed the following packages:
root@OpenWrt:/opt# opkg install kmod-scsi-core_3.10.49-1_ramips_24kec.ipk
root@OpenWrt:/opt# opkg install kmod-usb - Storage_3.10.49-1_ramips_24kec.ipk
root@OpenWrt:/opt# opkg install kmod-nls-iso8859-1_3.10.49-1_ramips_24kec.ipk
root@OpenWrt:/opt# opkg install kmod-nls-cp437_3.10.49-1_ramips_24kec.ipk
Root @OpenWrt:/opt# opkg install kmod-fs-vfat_3.10.49-1_ramips_24kec.ipk
root@OpenWrt:/opt# opkg install kmod-lib-crc16_3.10.49-1_ramips_24kec.ipk
root@OpenWrt:/opt# opkg install kmod - Crypto-core_3.10.49-1_ramips_24kec.ipk
root@OpenWrt:/opt# opkg install kmod-crypto-hash_3.10.49-1_ramips_24kec.ipk
Root@OpenWrt:/opt# opkg install kmod-fs-ext4_3.10.49-1_ramips_24kec.ipk

everything working fine with mounts

I have now partitioned my flash disk with fdisk. Done.
I installed e2fsprogs.
After I runned mkfs.ext4 /dev/ Sda1 (56GB)
I got "Writing superblocks and filesystem accounting information: Bus error"

root@OpenWrt:~# reboot
Segmentation fault

afer hard reset:
[ 19.010000] <==== rt28xx_init, Status=0
[ 19.870000] br-lan: Port 1( Eth0.1) entered forwarding state
[ 22.970000] jffs2: notice: (290) check_node_data: wrong data CRC in data node at 0x00c98c30: read 0x10b21581, calculated 0xcaf8212a.
[ 24.800000] device ra0 entered promiscuous mode
[ 24.800000] br-lan: port 2(ra0) entered forwarding state
[ 24.810000] br-lan: port 2(ra0) entered forwarding state
[ 26.810000] br-lan: port 2(ra0) entered forwarding state
[ 26.830000] !! ! APCLI LINK UP - IF(apcli0) AuthMode(7)=WPA2PSK, WepStatus(6)=AES !!!
[ 26.840000] /opt/sdk/wrtnode-sdk/build_dir/target-mipsel_24kec+dsp_uClibc-0.9.33.2/linux -ramips_mt7620n/rt2860v2-ApSoc_wifi_2720_12_05/rt2860v2_ap/../rt2860v2/ap/ap_data.c:4446 assert pEntry->Aid == pRxWI->WirelessCliIDfailed
[ 30.400000] jffs2: notice: (290) check_node_data: wrong data CRC in data node At 0x00369b34: read 0xacabae53, calculated 0x15a68daa.
[ 30.760000] jffs2: notice: (290) check_node_data: wrong data CRC in data node at 0x003337e8: read 0x198051ba, calculated 0xe8d7c191.
[ 30.770000] jffs2: warning: (290) jffs2_do_read_inode_internal: Truncating ino #618 to 656 bytes failed because it only had 0 bytes to start with!
[ 30.850000] jffs2: notice: (290) check_node_data: wrong data CRC in data node at 0x0032cabc : read 0x57fe2d07, calculated 0x12323b6c.
[ 31.540000] jffs2: notice: (290) check_node_data: wrong data CRC in data node at 0x002f0554: read 0x5629f645, calculated 0x920c7973.
[ 31.560000] jffs2: notice: (290) check_node_data: wrong data CRC in Data node at 0x0030ed04: read 0xe79efd9a, calculated 0xf9b5877b.
[ 31.600000] jffs2: notice: (290) check_node_data: wrong data CRC in data node at 0x0030972c: read 0x7c7e5ab9, calculated 0x90bc8d28.

I day before I also had same issue after installing some other packages. Therefore I have reinstalled the whole system yesterday.
Is it related to e2fsprogs or kmod-lib-crc16?
kmod-lib-crc16 is comming from my own build.
 
By now nothing is working. ie ls / works. But luci(Bad Gatewa), others not.
已邀请:

xzmu - 10w

赞同来自:

you can built-in the module by select the module using y not M, it means you don't need to install module atfer flash the firmware.

要回复问题请先登录注册