LEDE 系统固件烧写后无法进入控制台?


[    0.287311] console [ttyS0] enabled
[    0.300949] bootconsole [early0] disabled
[    0.300949] bootconsole [early0] disabled
[    0.318310] spi-mt7621 10000b00.spi: sys_freq: 191666666
[    0.333463] m25p80 spi32766.0: using chunked io (size=32)
[    0.344229] m25p80 spi32766.0: mx25l12805d (16384 Kbytes)
[    0.354959] 4 ofpart partitions found on MTD device spi32766.0
[    0.366515] Creating 4 MTD partitions on "spi32766.0":
[    0.376704] 0x000000000000-0x000000030000 : "u-boot"
[    0.388492] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.401114] 0x000000040000-0x000000050000 : "factory"
[    0.413217] 0x000000050000-0x000000800000 : "firmware"
[    0.450541] 2 uimage-fw partitions found on MTD device firmware
[    0.462305] 0x000000050000-0x000000185aa1 : "kernel"
[    0.473977] 0x000000185aa1-0x000000800000 : "rootfs"
[    0.485867] mtd: device 5 (rootfs) set to be root filesystem
[    0.497240] 1 squashfs-split partitions found on MTD device rootfs
[    0.509514] 0x000000370000-0x000000800000 : "rootfs_data"
[    0.532119] rt3050-esw 10110000.esw: link changed 0x00
[    0.544046] mtk_soc_eth 10100000.ethernet: generated random MAC address 0a:8a                  :29:f0:07:1b
[    0.561126] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0                  100000, irq 5
[    0.578070] mt7621_wdt 10000120.watchdog: Initialized
[    0.589673] NET: Registered protocol family 10
[    0.602284] NET: Registered protocol family 17
[    0.611255] bridge: automatic filtering via arp/ip/ip6tables has been depreca                  ted. Update your scripts to load br_netfilter if you need this.
[    0.636264] 8021q: 802.1Q VLAN Support v1.8
[    0.655855] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.670989] Freeing unused kernel memory: 200K
[    0.699725] Starting init: /etc/preinit exists but couldn't execute it (error                   -13)
[    1.715008] init: Console is alive
[    1.721961] init: - watchdog -
[    2.895957] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.099632] usbcore: registered new interface driver usbfs
[    3.110677] usbcore: registered new interface driver hub
[    3.121346] usbcore: registered new device driver usb
[    3.137579] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.152265] ehci-platform: EHCI generic platform driver
[    3.172921] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
[    3.186207] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[    3.196590] ehci-platform 101c0000.ehci: EHCI Host Controller
[    3.208033] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    3.223866] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    3.253837] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    3.267435] hub 1-0:1.0: USB hub found
[    3.275335] hub 1-0:1.0: 1 port detected
[    3.286481] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.300374] ohci-platform: OHCI generic platform driver
[    3.311054] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    3.324567] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    3.340344] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    3.408952] hub 2-0:1.0: USB hub found
[    3.416906] hub 2-0:1.0: 1 port detected
[    3.427428] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.452247] init: - preinit -
[    4.855526] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.030241] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    8.048043] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.091476] procd: - early -
[    8.098050] procd: - watchdog -
[    8.654695] rt3050-esw 10110000.esw: link changed 0x01
[    8.741119] procd: - watchdog -
[    8.747687] procd: - ubus -
[    8.944688] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    8.963018] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    8.980904] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    8.999110] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    9.016976] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    9.034947] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    9.052935] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[    9.071129] procd: - init -
Please press Enter to activate this console.
[    9.661307] random: jshn: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[    9.767359] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[    9.785493] random: ubus: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[   81.663838] random: nonblocking pool is initialized

Failed to executPlease press Enter to activate this console.

Failed to executPlease press Enter to activate this console.

Failed to executPlease press Enter to activate this console.

已邀请:

xzmu - 10w

赞同来自:

自编译固件?无解。只能查自己编译进去了什么东西导致ubus无法启动

要回复问题请先登录注册