新买的wrtnode 2P,上电后无WIFI,插网线也没有获取IP地址。串口连接看似正常,怎么破?

*[04030D0A][04020C0D]

DDR Calibration DQS reg = 0000878A



U-Boot 1.1.3 (Dec 6 2017 - 14:41:18)


Board: Ralink APSoC DRAM: 128 MB

relocate_code Pointer at: 87f60000

flash manufacture id: ef, device id 40 19

find flash: W25Q256FV

============================================

FM-02 UBoot Version: 1.0.0.1

--------------------------------------------

ASIC 7628_MP (Port5<->None)

DRAM component: 1024 Mbits DDR, width 16

DRAM bus: 16 bit

Total memory: 128 MBytes

Flash component: SPI Flash

Date:Dec 6 2017 Time:14:41:18

============================================

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768


##### The CPU freq = 575 MHZ ####

estimate memory size =128 Mbytes

RESET MT7628 PHY!!!!!!

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

0



3: System Boot system code via Flash.

## Booting image at bc050000 ...

Image Name: MIPS OpenWrt Linux-3.18.29

Image Type: MIPS Linux Kernel Image (lzma compressed)

Data Size: 1173057 Bytes = 1.1 MB

Load Address: 80000000

Entry Point: 80000000

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 128


Starting kernel ...


[ 0.000000] Linux version 3.18.29 (xx@build) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49363) ) #154 Thu Jan 10 17:08:08 CST 2019
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] MIPS: machine is WRTnode2P
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00025341
[ 0.000000] Readback ErrCtl register=00025341
[ 0.000000] Memory: 126212K/131072K available (2593K kernel code, 132K rwdata, 536K rodata, 184K init, 187K bss, 4860K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] intc: using register map from devicetree
[ 0.000000] CPU Clock: 575MHz
[ 0.000000] clocksource_of_init: no matching clocksources found
[ 0.000000] Calibrating delay loop... 380.92 BogoMIPS (lpj=1904640)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.080000] NET: Registered protocol family 16
[ 0.190000] mt7620-pci 10140000.pcie: Port 0 N_FTS = 1b105000
[ 0.340000] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK)
[ 0.350000] mt7620-pci: probe of 10140000.pcie failed with error -1
[ 0.360000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.370000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.370000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.380000] Switched to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.400000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP: reno registered
[ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.420000] NET: Registered protocol family 1
[ 0.430000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.450000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.470000] msgmni has been set to 246
[ 0.470000] io scheduler noop registered
[ 0.470000] io scheduler deadline registered (default)
[ 0.480000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[336]
[ 0.490000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[350]
[ 0.490000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.500000] console [ttyS0] disabled
[ 0.500000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[ 0.510000] console [ttyS0] enabled
[ 0.510000] console [ttyS0] enabled
[ 0.520000] bootconsole [early0] disabled
[ 0.520000] bootconsole [early0] disabled
[ 0.530000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
[ 0.540000] MT7628/7688 SPI Driver By WRTnode Team !
[ 0.540000] spi-mt7621 10000b00.spi: sys_freq: 191666666
[ 0.550000] m25p80 spi32766.0: w25q256 (32768 Kbytes)
[ 0.560000] m25p80 spi32766.0: using chunked io
[ 0.560000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.570000] Creating 4 MTD partitions on "spi32766.0":
[ 0.570000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.580000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.590000] 0x000000040000-0x000000050000 : "factory"
[ 0.590000] 0x000000050000-0x000002000000 : "firmware"
[ 0.730000] 2 uimage-fw partitions found on MTD device firmware
[ 0.730000] 0x000000050000-0x00000016e681 : "kernel"
[ 0.740000] 0x00000016e681-0x000002000000 : "rootfs"
[ 0.740000] mtd: device 5 (rootfs) set to be root filesystem
[ 0.750000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.760000] 0x0000006c0000-0x000002000000 : "rootfs_data"
[ 0.770000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[ 0.780000] i2c /dev entries driver
[ 0.790000] mt7621_wdt 10000120.watchdog: Initialized
[ 0.790000] TCP: cubic registered
[ 0.790000] NET: Registered protocol family 17
[ 0.800000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.810000] 8021q: 802.1Q VLAN Support v1.8
[ 0.830000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.840000] Freeing unused kernel memory: 184K (80332000 - 80360000)
[ 2.590000] init: Console is alive
[ 2.590000] init: - watchdog -
[ 5.390000] usbcore: registered new interface driver usbfs
[ 5.390000] usbcore: registered new interface driver hub
[ 5.400000] usbcore: registered new device driver usb
[ 5.440000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.440000] ehci-platform: EHCI generic platform driver
[ 5.620000] U2PHY P0 set SRCTRL calibration value: 6
[ 5.620000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 5.630000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 5.630000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 5.660000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 5.660000] hub 1-0:1.0: USB hub found
[ 5.670000] hub 1-0:1.0: 1 port detected
[ 5.670000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.680000] ohci-platform: OHCI generic platform driver
[ 5.690000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 5.690000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 5.700000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 5.770000] hub 2-0:1.0: USB hub found
[ 5.770000] hub 2-0:1.0: 1 port detected
[ 5.790000] MTK MSDC device init.
[ 5.830000] mtk-sd: MediaTek MT6575 MSDC Driver
[ 5.830000] sdhci: Secure Digital Host Controller Interface driver
[ 5.840000] sdhci: Copyright(c) Pierre Ossman
[ 5.840000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 6.640000] init: - preinit -
[ 7.860000] rt305x-esw 10110000.esw: link changed 0x00
[ 8.050000] random: mktemp urandom read with 13 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 11.310000] mount_root: loading kmods from internal overlay
[ 12.140000] jffs2: notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 12.160000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.170000] block: extroot: not configured
[ 12.430000] jffs2: notice: (344) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 12.920000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.940000] block: extroot: not configured
[ 12.940000] mount_root: switching to jffs2 overlay
[ 12.970000] procd: - early -
[ 12.980000] procd: - watchdog -
[ 13.700000] procd: - ubus -
[ 14.710000] procd: - init -
Please press Enter to activate this console.
[ 15.770000] NET: Registered protocol family 10
[ 15.820000] RPC: Registered named UNIX socket transport module.
[ 15.820000] RPC: Registered udp transport module.
[ 15.830000] RPC: Registered tcp transport module.
[ 15.830000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 15.850000] tun: Universal TUN/TAP device driver, 1.6
[ 15.850000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 15.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.900000] Ralink/MTK WiFi EEPROM API Build for MT7620.

[ 15.940000] WRTnode AP Driver version: 4.1.0.0
[ 15.950000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.970000] nf_conntrack version 0.5.0 (1974 buckets, 7896 max)
[ 16.020000] usbcore: registered new interface driver usbserial
[ 16.020000] usbcore: registered new interface driver usbserial_generic
[ 16.030000] usbserial: USB Serial support registered for generic
[ 16.070000] xt_time: kernel timezone is -0000
[ 16.090000] PPP generic driver version 2.4.2
[ 16.100000] PPP MPPE Compression module registered
[ 16.110000] NET: Registered protocol family 24
[ 16.110000] usbcore: registered new interface driver sierra
[ 16.120000] usbserial: USB Serial support registered for Sierra USB modem
[ 16.130000] usbcore: registered new interface driver usb_serial_simple
[ 16.130000] usbserial: USB Serial support registered for carelink
[ 16.140000] usbserial: USB Serial support registered for zio
[ 16.150000] usbserial: USB Serial support registered for funsoft
[ 16.150000] usbserial: USB Serial support registered for flashloader
[ 16.160000] usbserial: USB Serial support registered for vivopay
[ 16.170000] usbserial: USB Serial support registered for moto_modem
[ 16.170000] usbserial: USB Serial support registered for novatel_gps
[ 16.180000] usbserial: USB Serial support registered for hp4x
[ 16.180000] usbserial: USB Serial support registered for suunto
[ 16.190000] usbserial: USB Serial support registered for siemens_mpi
[ 16.200000] usbcore: registered new interface driver option
[ 16.210000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.220000] usbcore: registered new interface driver qcserial
[ 16.230000] usbserial: USB Serial support registered for Qualcomm USB modem
[ 22.000000] device eth0.1 entered promiscuous mode
[ 22.000000] device eth0 entered promiscuous mode
[ 22.030000] br-lan: port 1(eth0.1) entered forwarding state
[ 22.030000] br-lan: port 1(eth0.1) entered forwarding state
[ 24.030000] br-lan: port 1(eth0.1) entered forwarding state
[ 79.680000] random: nonblocking pool is initialized
已邀请:

xzmu - 10w

赞同来自:

从日志上看,是官方固件,但是不确定这个固件的配置有没有被改过。所以你做一下恢复出厂设置,串口按回车进去,输入 firstboot -y 然后重启设备。

YIWA

赞同来自:

好的 感谢

YIWA

赞同来自:

按照此方法做了,但是还是没有WIFI

xzmu - 10w

赞同来自:

cat /etc/config/network 还有 cat /etc/config/wireless我看一下
 
或者 直接用串口启动的时候按2 刷这个固件 http://wrtnode.cc/d/wrtnode2p-firmware.bin
刷的方法参考下这个 http://wiki.wrtnode.cc/index.p ... %2596

YIWA

赞同来自:

最后发现是因为核心板和底板得接触似乎有些问题。换了一块核心板就好了。
 
然后我又买了一块wrtnode2p。今天刚上电测试 一样问题。但目前没去管。

要回复问题请先登录注册