使用官方18.06.2的固件无led,usb没有反应

https://downloads.openwrt.org/releases/18.06.2/targets/ramips/mt7620/openwrt-18.06.2-ramips-mt7620-wrtnode-squashfs-sysupgrade.bin
 
 
是否可以直接使用官方的固件呢,刷入后wifi可用,但是板子led灯不亮,底板的usb插入设备后无反应
已邀请:

xzmu - 10w

赞同来自:

关于hub无反应,是否方便提供下dmesg输出的日志。哪一颗led不亮?还是都不亮?

lxm

赞同来自:

进入系统后一个都不会亮
 
[    0.000000] Linux version 4.14.95 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7627-753531d)) #0 Mon Jan 28 08:54:32 2019
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is WRTNODE
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 80421050, node_mem_map 81000040
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] random: get_random_bytes called from 0x8042472c with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00077292
[    0.000000] Readback ErrCtl register=00077292
[    0.000000] Memory: 60256K/65536K available (3590K kernel code, 178K rwdata, 464K rodata, 176K init, 214K bss, 5280K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 600MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000011] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[    0.007595] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
[    0.073576] pid_max: default: 32768 minimum: 301
[    0.078314] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084680] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.096204] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.105762] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.111731] pinctrl core: initialized pinctrl subsystem
[    0.118038] NET: Registered protocol family 16
[    0.127115] Can't analyze schedule() prologue at 8037d498
[    0.149561] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.154956] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.161339] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.166712] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.173053] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.178435] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.184792] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.190081] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.201186] clocksource: Switched to clocksource systick
[    0.207464] NET: Registered protocol family 2
[    0.212633] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.219361] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.225579] TCP: Hash tables configured (established 1024 bind 1024)
[    0.231841] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.237466] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.243844] NET: Registered protocol family 1
[    0.248034] PCI: CLS 0 bytes, default 32
[    0.250700] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.257390] Crashlog allocated RAM at address 0x3f00000
[    0.264146] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.276173] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.281815] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.301544] io scheduler noop registered
[    0.305290] io scheduler deadline registered (default)
[    0.311248] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.320241] console [ttyS0] disabled
[    0.323746] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.333353] console [ttyS0] enabled
[    0.347136] bootconsole [early0] disabled
[    0.363666] cacheinfo: Failed to find cpu0 device node
[    0.373933] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.393190] spi spi0.0: force spi mode3
[    0.411789] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.421221] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.433880] Creating 4 MTD partitions on "spi0.0":
[    0.443437] 0x000000000000-0x000000030000 : "u-boot"
[    0.454215] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.465688] 0x000000040000-0x000000050000 : "factory"
[    0.476650] 0x000000050000-0x000001000000 : "firmware"
[    2.315596] 2 uimage-fw partitions found on MTD device firmware
[    2.327429] 0x000000050000-0x0000001aecea : "kernel"
[    2.338181] 0x0000001aecea-0x000001000000 : "rootfs"
[    2.348925] mtd: device 5 (rootfs) set to be root filesystem
[    2.361812] 1 squashfs-split partitions found on MTD device rootfs
[    2.374175] 0x0000003f3000-0x000001000000 : "rootfs_data"
[    2.386516] libphy: Fixed MDIO Bus: probed
[    2.399467] gsw: setting port4 to ephy mode
[    2.407876] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 3 link up (100Mbps/Full duplex)
[    2.426295] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    2.438770] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    2.455771] rt2880_wdt 10000120.watchdog: Initialized
[    2.467213] NET: Registered protocol family 10
[    2.479891] Segment Routing with IPv6
[    2.487374] NET: Registered protocol family 17
[    2.496284] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.522108] 8021q: 802.1Q VLAN Support v1.8
[    2.547409] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.561513] random: fast init done
[    2.569207] Freeing unused kernel memory: 176K
[    2.578084] This architecture does not have kernel memory protection.
[    4.052494] init: Console is alive
[    4.059499] init: - watchdog -
[    5.602285] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.914171] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.932665] init: - preinit -
[    7.590006] 8021q: adding VLAN 0 to HW filter on device eth0
[    7.746306] random: procd: uninitialized urandom read (4 bytes read)
[   10.618227] jffs2: notice: (358) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (0 unchecked, 3 orphan) and 3 of xref (3 dead, 0 orphan) found.
[   10.651891] mount_root: switching to jffs2 overlay
[   10.695081] overlayfs: upper fs does not support tmpfile.
[   10.716106] urandom-seed: Seeding with /etc/urandom.seed
[   10.994702] procd: - early -
[   11.001333] procd: - watchdog -
[   11.332479] procd: - watchdog -
[   11.339033] procd: - ubus -
[   11.561935] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.579123] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.592463] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.606291] procd: - init -
[   12.153504] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.263434] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.286383] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   12.302409] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   12.319959] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.339434] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   12.413510] xt_time: kernel timezone is -0000
[   12.499514] PPP generic driver version 2.4.2
[   12.510851] NET: Registered protocol family 24
[   12.548613] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[   12.563081] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[   12.578528] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   12.592889] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   12.667680] kmodloader: done loading kernel modules from /etc/modules.d/*
[   13.971321] urandom_read: 5 callbacks suppressed
[   13.971330] random: jshn: uninitialized urandom read (4 bytes read)
[   23.285448] 8021q: adding VLAN 0 to HW filter on device eth0
[   23.332008] br-lan: port 1(eth0.1) entered blocking state
[   23.342840] br-lan: port 1(eth0.1) entered disabled state
[   23.353963] device eth0.1 entered promiscuous mode
[   23.363546] device eth0 entered promiscuous mode
[   23.530642] br-lan: port 1(eth0.1) entered blocking state
[   23.541463] br-lan: port 1(eth0.1) entered forwarding state
[   23.552763] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   24.342600] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   27.864172] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[   27.883231] br-lan: port 2(wlan0-1) entered blocking state
[   27.894234] br-lan: port 2(wlan0-1) entered disabled state
[   27.905556] device wlan0-1 entered promiscuous mode
[   28.038482] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   30.472551] wlan0: authenticate with 60:45:cb:68:28:98
[   30.507969] wlan0: send auth to 60:45:cb:68:28:98 (try 1/3)
[   30.529986] wlan0: authenticated
[   30.549970] wlan0: associate with 60:45:cb:68:28:98 (try 1/3)
[   30.578010] wlan0: RX AssocResp from 60:45:cb:68:28:98 (capab=0x1011 status=0 aid=9)
[   30.593849] wlan0: associated
[   30.731751] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   30.762987] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[   30.776607] br-lan: port 2(wlan0-1) entered blocking state
[   30.787610] br-lan: port 2(wlan0-1) entered forwarding state
[   45.781105] random: crng init done
 

xzmu - 10w

赞同来自:

似乎是没选usb驱动,灯不亮的原因是默认软件没配置led灯,需要改dts

要回复问题请先登录注册