Failed to executPlease press Enter to activate this console.

U-Boot 1.1.3 (Jan 13 2018 - 18:54:47)
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:18:54:47
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 575 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Press the [1] key when power on to enter web upgrade mode

Continue normal boot...

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
5: Entr ALL LED test mode.
6: Entr Web failsafe mode.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
Image Name: MIPS LEDE Linux-4.4.194
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1278978 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[ 0.000000] Linux version 4.4.194 (root@ubuntu) (gcc version 5.4.0 (LEDE GCC 5.4.0 unknown) ) #0 Tue Nov 19 05:51:15 2019
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Mediatek MT7628AN evaluation board
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0006ec4f
[ 0.000000] Readback ErrCtl register=0006ec4f
[ 0.000000] Memory: 60720K/65536K available (2951K kernel code, 141K rwdata, 700K rodata, 168K init, 187K bss, 4816K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] intc: using register map from devicetree
[ 0.000000] CPU Clock: 575MHz
[ 0.000000] clocksource_probe: no matching clocksources found
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6647862422 ns
[ 0.000012] sched_clock: 32 bits at 287MHz, resolution 3ns, wraps every 7469508094ns
[ 0.007875] Calibrating delay loop... 380.92 BogoMIPS (lpj=1904640)
[ 0.070477] pid_max: default: 32768 minimum: 301
[ 0.075291] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081933] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.095916] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.105882] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112171] pinctrl core: initialized pinctrl subsystem
[ 0.118190] NET: Registered protocol family 16
[ 0.125594] pinctrl core: failed to register map default (0): invalid type given
[ 0.149628] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.155423] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.161091] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.168302] clocksource: Switched to clocksource MIPS
[ 0.174881] NET: Registered protocol family 2
[ 0.180234] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.187243] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.193725] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.200206] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.206068] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.212762] NET: Registered protocol family 1
[ 0.223084] Crashlog allocated RAM at address 0x3f00000
[ 0.245939] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.251862] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.264815] io scheduler noop registered
[ 0.268793] io scheduler deadline registered (default)
[ 0.275796] gpio-export gpio_export: 11 gpio(s) exported
[ 0.281477] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.289208] console [ttyS0] disabled
[ 0.292802] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[ 0.301994] console [ttyS0] enabled
[ 0.301994] console [ttyS0] enabled
[ 0.308985] bootconsole [early0] disabled
[ 0.308985] bootconsole [early0] disabled
[ 0.318566] spi-mt7621 10000b00.spi: sys_freq: 191666666
[ 0.330033] m25p80 spi32766.0: using chunked io (size=32)
[ 0.335531] m25p80 spi32766.0: w25q256 (32768 Kbytes)
[ 0.340744] 4 ofpart partitions found on MTD device spi32766.0
[ 0.346656] Creating 4 MTD partitions on "spi32766.0":
[ 0.351885] 0x000000000000-0x000000030000 : "u-boot"
[ 0.358929] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.366320] 0x000000040000-0x000000050000 : "factory"
[ 0.373512] 0x000000050000-0x000001000000 : "firmware"
[ 0.432954] 2 uimage-fw partitions found on MTD device firmware
[ 0.439017] 0x000000050000-0x000000188442 : "kernel"
[ 0.445807] 0x000000188442-0x000001000000 : "rootfs"
[ 0.452923] mtd: device 5 (rootfs) set to be root filesystem
[ 0.458841] 1 squashfs-split partitions found on MTD device rootfs
[ 0.465119] 0x000000470000-0x000001000000 : "rootfs_data"
[ 0.482253] rt3050-esw 10110000.esw: link changed 0x00
[ 0.489161] mtk_soc_eth 10100000.ethernet: generated random MAC address 16:87:7b:a9:73:37
[ 0.498364] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.507252] mt7621_wdt 10000120.watchdog: Initialized
[ 0.513977] NET: Registered protocol family 10
[ 0.522033] NET: Registered protocol family 17
[ 0.526625] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.539494] 8021q: 802.1Q VLAN Support v1.8
[ 0.553588] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.561732] Freeing unused kernel memory: 168K
[ 2.105313] init: Console is alive
[ 2.109149] init: - watchdog -
[ 3.477798] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.580675] usbcore: registered new interface driver usbfs
[ 3.586340] usbcore: registered new interface driver hub
[ 3.591932] usbcore: registered new device driver usb
[ 3.601111] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.609254] ehci-platform: EHCI generic platform driver
[ 3.624837] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
[ 3.631648] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[ 3.636976] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.642846] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.651009] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.668322] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.675817] hub 1-0:1.0: USB hub found
[ 3.680134] hub 1-0:1.0: 1 port detected
[ 3.687243] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.695135] ohci-platform: OHCI generic platform driver
[ 3.700786] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 3.707727] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 3.715869] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 3.783567] hub 2-0:1.0: USB hub found
[ 3.787774] hub 2-0:1.0: 1 port detected
[ 3.804098] MTK MSDC device init.
[ 3.807642] mtk-sd: MediaTek MT6575 MSDC Driver
[ 3.814690] sdhci: Secure Digital Host Controller Interface driver
[ 3.821030] sdhci: Copyright(c) Pierre Ossman
[ 3.826814] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.835893] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.846205] init: - preinit -
[ 5.020002] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.426685] jffs2: notice: (338) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.445313] mount_root: switching to jffs2 overlay
[ 8.460739] urandom-seed: Seeding with /etc/urandom.seed
[ 8.596323] procd: - early -
[ 8.600084] procd: - watchdog -
[ 9.248471] procd: - watchdog -
[ 9.251942] procd: - ubus -
[ 9.306348] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.316058] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.325282] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.334843] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.344059] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.354428] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.363787] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.373356] procd: - init -
Please press Enter to activate this console.

Failed to executPlease press Enter to activate this console.
^CPlease press Enter to activate this console.
[ 81.638346] random: nonblocking pool is initialized
^CPlease press Enter to activate this console.

Failed to executPlease press Enter to activate this console.

Failed to executPlease press Enter to activate this console.

Failed to execut

Please press EntPlease press Enter to activate this console.
^CPlease press Enter to activate this console.

已邀请:

xzmu - 10w

赞同来自:

the bash can't running, please check the code or rebuild the firmware

要回复问题请先登录注册